Euro Pro Iron GI490H User Manual

Model GI490H  
LIMITED WARRANTY  
ONE (1) YEAR LIMITED WARRANTY  
EURO-PRO OPERATING LLC warrants this product to be free from defects in material and  
workmanship for a period of one (1) year from the date of the original purchase, when utilized for  
normal household use, subject to the following conditions, exclusions and exceptions.  
If your appliance fails to operate properly while in use under normal household conditions within  
the warranty period, return the complete appliance and accessories, freight prepaid to  
Intelligent Electronic 1700 Watt Iron  
EURO-PRO Operating LLC, 21 Lawrence Paquette Ind. Dr., Champlain, N.Y. 12919  
If the appliance is found by EURO-PRO Operating LLC to be defective in material or  
workmanship, EURO-PRO will repair or replace it free of charge. Proof of purchase date and $  
9.95 to cover the cost of return shipping and handling must be included.*  
OWNER’S MANUAL  
Model GI490H  
The liability of EURO-PRO Operating LLC is limited solely to the cost of the repair or replacement  
of the unit at our option. This warranty does not cover normal wear of parts and does not apply to  
any unit that has been tampered with or used for commercial purposes. This limited warranty does  
not cover damage caused by misuse, abuse, negligent handling or damage due to faulty  
packaging or mishandling in transit. This warranty does not cover damage or defects caused by  
or resulting from damages from shipping or repairs, service or alterations to the product or any of  
its parts, which have been performed by a repair person not authorized by EURO-PRO Operating  
LLC.  
120V., 60 Hz., 1700 Watts  
This warranty is extended to the original purchaser of the unit and excludes all other legal and/or  
conventional warranties. The responsibility of EURO-PRO Operating LLC if any, is limited to the  
specific obligations expressly assumed by it under the terms of the limited warranty. In no event is  
EURO-PRO Operating LLC liable for incidental or consequential damages of any nature  
whatsoever. Some states do not permit the exclusion or limitation of incidental or consequential  
damages, so the above may not apply to you.  
This warranty gives you specific legal rights, and you may also have other rights which vary from  
state to state.  
*IMPORTANT: Carefully pack item to avoid damage in shipping. Be sure to include proof of  
purchase date and to attach tag to item before packing with your name, complete address  
and phone number with a note giving purchase information, model number and what you  
believe is the problem with item. We recommend you insure the package (as damage in  
shipping is not covered by your warranty). Mark the outside of your package “ATTENTION  
CUSTOMER SERVICE”. We are constantly striving to improve our products, therefore the  
specifications contained herein are subject to change without notice.  
PRODUCT REGISTRATION CARD  
Please complete and return within ten (10) days of purchase. The registration will enable us to  
contact you in the event a product defect is discovered. By returning this card you acknowledge  
to have read and understood the instructions for use, and warnings set forth in the accompanying  
instructions.  
RETURN TO: EURO-PRO Operating LLC, 21 LAWRENCE PAQUETTE IND. DR., CHAMPLAIN, N.Y. 12919  
PURCHASER: ……………………………………………………………………………………………  
ADDRESS: ……………………………………………………………………………………………….  
For information or assistance:  
EURO-PRO Operating LLC  
21 Lawrence Paquette Industrial Drive  
Champlain, NY 12919  
GI490H  
DATE OF PURCHASE: …………………….. MODEL: ………………. SERIAL NO: .…………….  
NAME AND ADDRESS OF STORE: …………………………………………………………………..  
Tel. 1 (800) 798-7398  
Printed in China  
 
GETTING TO KNOW YOUR INTELLIGENT  
ELECTRONIC IRON  
IRONING CHART  
NOTE: Always refer to the garment  
To select iron temperature, align  
temperature selected on dial with  
the indicator on the water tank.  
The odor is safe and should not reoccur  
after initial heating.  
Before using your Intelligent Electronic  
care tag for ironing instructions. Before  
starting to iron delicate fabrics, it is best  
to first test the temperature of the iron  
on a hem or an inside seam.  
Iron, remove any labels, stickers or tags  
that may be attached to the body or  
soleplate of the iron.  
When turned on for the first time, your  
new iron may emit an odor for up to 10  
minutes. This is due to the initial  
heating of the materials used in making  
the iron.  
Also, before ironing with steam for the  
first time, allow iron to heat, hold in a  
horizontal position and hit the burst of  
steam button several times. The iron  
may emit some small particles from the  
steam holes. This is normal and will  
clear after pressing the burst of steam  
button several times.  
DIRECTIONS  
ON LABEL  
Display Panel  
SYNTHETIC  
FIBERS, e.g.  
acrylic, nylon  
polyester  
SILK  
COTTON  
LINEN  
FABRIC  
WOOL  
13  
14  
LED  
DISPLAY  
PANEL  
MIN  
MAX  
• • • • •  
12  
MINIMUM  
STEAM  
MAXIMUM  
STEAM  
STEAM  
CONTROL  
0
11  
BURST OF  
STEAM  
1. Electronic Temperature Control  
2. Display Panel  
3. Atomizer Spray Button  
4. Burst of Steam/X-Tended  
Steam Burst Button  
8. Water Level Window  
9. Stainless Steel Soleplate  
10. Handle  
11. Auto-Off Light  
12. Power Light  
SPRAY  
5. variable steam control  
6. Water Inlet Door  
7. Spray Nozzle  
13. Fabric & Steam Settings  
14. Temperature Indicators  
15. Water Flask  
9
2
 
FEATURES OF THE INTELLIGENT ELECTRONIC IRON  
OPERATING INSTRUCTIONS (CONT.)  
LED Display Panel  
3
STORAGE  
NOTE: The anti drip function reduces  
water dripping and water stains. It does  
not prevent water dripping and water  
stains if you press the steam burst  
button too often or if the temperature is  
too low. The amount of water droplets  
will eventually decrease after the iron is  
used for 2 to 3 tankfuls of steaming and  
ironing.  
1. Always turn the variable steam  
control to “0” after you have emptied  
the water tank.  
2. Allow the iron to cool down.  
3. Always store the iron in the upright  
position to protect the soleplate.  
4. From time to time, clean the exterior  
of the iron with a damp cloth and  
wipe dry.  
1 2  
5. If you use spray starch, wipe the  
soleplate occasionally with a soft  
damp cloth to prevent the build-up of  
deposits.  
4
1. BURST OF STEAM  
/X-TENDEDTM STEAM  
BURST  
6. LED DISPLAY PANEL  
Displays the fabric and the  
temperature settings.  
6. If the iron has not been used for a  
few weeks, hold the iron horizontally  
and allow to steam for 2 minutes  
before ironing.  
The X-TendedTM Steam Burst  
provides continuous, powerful  
steam performance. Can be used  
vertically as well as horizontally.  
The Burst of Steam provides  
extra, sudden blasts of steam  
which aid in removing stubborn  
wrinkles from fabrics such as  
denim, cotton or linen.  
7. WATER FILLING INLET  
The cover prevents dust and  
foreign matter from entering  
the water tank. It also stops  
any water from spilling during  
ironing.  
2. ATOMIZER SPRAY  
BUTTON  
Pressing this Button provides a  
defined jet of spray which gently  
moistens fabric.  
8. BUILT-IN ANTI-CALCIUM  
FILTER  
3. VARIABLE STEAM  
CONTROL  
Prevents calcium build-up  
and prolongs the life of the  
iron.  
Minimum to maximum steaming for  
different materials. Self cleaning  
feature flushes internal sole plate  
with water.  
9. STAINLESS STEEL  
SOLEPLATE  
Provides maximum glide-  
ability and heat retention.  
4. ELECTRONIC  
TEMPERATURE CONTROL  
Select the fabric setting by  
pressing on this button.  
10. PIVOT CORD  
For left or right handed use.  
Pivots up and down;  
5. Anti-Drip Function  
Cuts off water when the  
iron temperature is too  
low.  
prevents dragging along the  
fabric. The flexible cord  
protector protects the cord  
from fraying.  
3
8
 
OPERATING INSTRUCTIONS (CONT.)  
OPERATING INSTRUCTIONS  
ELECTRONIC AUTOMATIC  
SHUT-OFF  
SELF CLEANING  
This appliance is for HOUSEHOLD USE  
NOTE: Because of the soleplate design,  
ordinary tap water may be used with this  
iron. However, in very hard water areas,  
we recommend using distilled or  
demineralized water.  
It is important to “Self Clean” the iron at  
least every two weeks to remove scale,  
calcium, etc. The harder the water, the  
more often the iron should be self  
cleaned.  
ONLY and may be plugged into any  
120V AC polarized electrical outlet. Do  
not use any other type of outlet.  
The ELECTRONIC Iron is equipped with  
an electronic auto shut-off. The electronic  
auto-off switches the iron off if it has been  
left standing unmoved in any position  
(sideways, flat or upright) for  
approximately 7-9 minutes. A red light on  
the LED display panel will flash when the  
iron switches itself off. (Fig. 7) To switch  
the iron back on, just shake the iron side-  
to-side several times.  
DRY IRONING  
1. Set the variable steam control dial  
to any steam position.  
WARNING: Never fill the iron with  
fabric conditioner, starches or any  
other liquid, as these will damage the  
steam mechanism. Do not use  
contaminated water.  
All marked settings on the LED display  
panel can be used for dry ironing. Turn  
the variable steam control dial all the  
way to the right to “0”. This will cut off  
the steam flow if water is in the tank.  
2. Fill the water tank up to the “MAX”  
level.  
3. Stand the iron on its heel. Plug the  
iron into the electrical outlet.  
1. Open the water filling inlet cover.  
Holding the iron at a slight angle,  
pour water slowly into the water  
filling inlet. See figure 1. Fill tank to  
desired level or to the “MAX” water  
level marking using the water filling  
flask. (When the iron is upright, the  
see-through water tank allows you to  
gauge the amount of water.) DO  
NOT overfill the tank. When finished  
filling the iron with water, close the  
water inlet cover before continuing.  
1. Press on the electronic temperature  
control button to select the desired  
fabric/temperature setting. Turn the  
variable steam control dial to “0”.  
(See “Ironing Guide” for a guide to  
temperature selection.)  
4. Press the electronic temperature  
control button until you get the  
“MAX” temperature setting on the  
display panel and wait until the iron  
heats up and temperature setting  
light stops flashing.  
2. Plug the cord into a polarized, 120V  
AC electrical outlet. The power “ON”  
light will come on, indicating that the  
iron is receiving power.  
5. Turn the variable steam control dial  
to the self-cleaning position and hold  
the iron horizontally over the sink.  
(Fig. 8).  
3. Place iron on its heel (on a stable,  
protected surface) while iron is  
warming to desired temperature.  
6. Boiling water and steam will now be  
ejected from the holes in the  
soleplate. The impurities and scale  
are washed away with it.  
Flash  
Fig. 7  
STEAM IRONING  
7. Move the iron back and forth as this  
happens.  
EMPTYING THE IRON  
1. Always empty iron after each use.  
CAUTION! DO NOT aim iron at face,  
towards yourself, or anyone else  
while using or adjusting steam.  
Burns or serious injury may occur.  
8. If there is any water left in the water  
tank after the iron stops steaming,  
just empty the remaining water in a  
sink following the instructions for  
emptying the iron.  
2. When finished using the iron, turn  
the variable steam control dial to  
“0” and press the electronic  
temperature control button until the  
power light is lit.  
WARNING! Before filling the iron  
with water, be sure the iron is not  
plugged into the electrical outlet. The  
iron may be filled with water while it  
is hot.  
Fig. 1  
2. Plug the cord into a polarized, 120V  
AC electrical outlet.  
9. Turn the variable steam control dial to  
the “0” position when the water tank  
is empty.  
3. Unplug the iron from the electrical  
outlet.  
3. Press on the electronic temperature  
control button to select the desired  
fabric and temperature setting. Turn  
the variable steam control dial to  
the desired steam setting. (See  
“Ironing Guide” for a guide to  
4. Turn the iron upside down over the  
sink with the tip pointing downward  
and allow the water to flow from the  
opening.  
CAUTION! TO PREVENT THE RISK  
OF BURNS, use caution when filling  
iron with water. Burns can occur  
from touching hot metal parts, hot  
water, or steam.  
10.Place the iron back upright on its  
heel to cool down before storing.  
5. Place iron upright and allow to cool  
before storing.  
temperature selection.)  
CAUTION! Use caution when  
emptying the iron. Burns may occur  
from touching hot metal surfaces,  
hot water or steam.  
Fig. 8  
4
7
 
OPERATING INSTRUCTIONS (CONT.)  
OPERATING INSTRUCTIONS (CONT.)  
ATOMIZER SPRAY NOZZLE  
4. Place the iron on its heel on a stable,  
protected surface and allow the iron  
to heat for approximately two (2)  
minutes or until the temperature  
settings on the right side of the LED  
display panel have stopped flashing.  
5. Turn the variable steam control dial  
to the right to increase the amount of  
steam. When using extra steam, the  
iron uses more water and it may be  
necessary to fill the water tank more  
often. (Fig. 2)  
The atomizer spray nozzle is useful on  
fabrics with stubborn wrinkles. Press the  
spray button and a jet of water will spray  
onto the fabric being ironed. (Fig. 5) The  
water spray can be used with dry or  
steam ironing as desired.  
Temp.  
settings  
Fig. 3  
NOTE: If the tank runs dry, remove the  
plug from wall outlet. Then, fill the iron  
with water and re-prime the pump. The  
iron may be filled with water while it is  
hot.  
To use the X-TendedTM Steam Burst  
feature:  
Fig. 6  
IRONING HINTS  
Fig. 5  
4. Set the variable steam control dial  
to the desired steam setting.  
5. Turn the steam button to the  
maximum steam setting. (Fig. 4)  
6. Press the electronic temperature  
control button until you get to the  
desired fabric setting.  
7. To maintain a constant flow of  
steam, make sure that the water  
tank is at least half full.  
WARNING! To prevent fire, do not  
leave iron unattended while  
connected.  
SELECTING IRON TEMPERATURES  
Always read garment labels and follow  
the manufacturer’s ironing instructions.  
Refer to the “Ironing Chart” on page 12  
for temperature recommendations:  
Fig. 2  
Sort articles to be ironed according  
to the type of fabric. This will reduce  
the need to adjust the temperature  
for different types of garments.  
BURST OF STEAM/X-TENDEDTM  
STEAM  
Use low settings for nylon or other  
synthetics.  
CAUTION! DO NOT aim iron at face,  
towards yourself, or anyone else  
while using or adjusting steam.  
Burns or serious injury may occur.  
If you are not sure of the fiber  
content of a garment, test a small  
area such as a seam or inside hem  
section before ironing a visible area.  
Start with a low temperature setting  
and gradually increase to find the  
best setting.  
•• Use moderate settings for wool,  
silks, and blends.  
••• Use high settings for cottons and  
linens.  
The burst-of-steam button is useful  
when ironing denim, cotton, and linens.  
It provides extra, sudden blasts of  
steam which aid in removing stubborn  
wrinkles.  
1. Stand the iron upright on its heel.  
2. Plug the cord into a polarized, 120V  
AC electrical outlet.  
3. Press the electronic temperature  
control until you get the desired  
fabric/temperature setting.  
4. The light on the right side of the LED  
display panel will stop flashing when  
the desired temperature has been  
reached. (Fig. 6)  
When reducing the temperature to  
iron sensitive fabrics, allow  
approximately 2 minutes for the iron  
to cool to the new temperature  
setting.  
The burst-of-steam feature can be used  
with Dry or Steam ironing as desired.  
1. Make sure the water tank is at least  
1/2 filled with water.  
Fabrics such as velour, wool, linen  
and silk are best ironed with an  
ironing cloth to prevent shine marks.  
2. Set the desired fabric and  
temperature setting. Place the iron  
on its heel (on a stable, protected  
surface) and allow it to heat for  
approximately 2 minutes.  
Fig. 4  
3. Turn the steam button to the  
minimum steam setting. (Fig. 3)  
4. With the iron in a horizontal position,  
press the burst of steam button  
several times to prime the pump.  
5
6
 

Electro Voice Portable Speaker E V Eight A User Manual
Euro Pro Convection Oven JO287 User Manual
Everpure Water System EV9318 60 User Manual
Excalibur electronic MP3 Docking Station 133 User Manual
Extron electronic Stereo Amplifier MDA 3 Series User Manual
FEIN Power Tools Cordless Sander FMM250 User Manual
Fujitsu Server V80B10 User Manual
Fundex Games Board Games Jumpin Java User Manual
GE Thermostat RAK148D1 User Manual
GE Washer GCRH410 User Manual