Euro Pro Carpet Cleaner EP922H User Manual

Portable Steam Cleaner  
with Caddy  
OWNER’S MANUAL  
Model EP922H  
120V., 60 Hz, 1550 Watts  
EURO-PRO Operating LLC  
94 Main Mill Street, Door 16  
Plattsburgh, NY 12901  
Tel.: 1 (800) 798-7398  
 
TIPS ON HOW TO USE YOUR SYSTEM  
ADDITIONAL IMPORTANT SAFEGUARDS cont.  
Bathroom Areas cont.  
Hints  
1. To avoid circuit overload, do not operate another appliance on the same socket  
(circuit) as the steam cleaner.  
2. If an extension cord is absolutely necessary, an extension cord rated a minimum  
of 15 ampere, 14 gage cord should be used. Cords rated for less amperage may  
overheat. Care should be taken to arrange cord so that it cannot be pulled or  
tripped over.  
To clean sanitary fixtures, use the  
concentrator with or without detail  
brush. Use a terry cloth towel or paper  
towel to wipe up excess moisture and  
residue.  
ALWAYS FINISH CLEANING BY WIPING  
DOWN THE CLEANED SURFACE WITH A  
TOWEL  
The portable steam cleaner has many  
uses that have not been mentioned.  
This was meant only to give you a  
general idea of what can be achieved  
with the unit. However, the ways in  
which to use the attachments and  
brushes are in most cases universal. It  
is most helpful to always have a terry  
cloth towel or paper towel ready to use  
for removal of moisture and residue.  
100% white cotton towels work best.  
You can clean the brushes with your  
steam cleaner. To clean the floor brush,  
hold at one end and use the  
To clean the sink and faucets, use detail  
brush then finish by wiping with a towel.  
3. Do not leave unattended when the system is connected to a power  
supply/electrical outlet.  
Automotive  
To clean inside your car, use the floor  
brush with a terry cloth towel attached  
to clean upholstery and interior areas  
just as in the home. You should not  
expose the bristles to leather - use only  
the brush with the terry cloth towel  
attached. For detailing the wheels, use  
the concentrator and the detail brush.  
Exterior windows are cleaned best by  
applying the vapor with the concentrator  
and following with a paper towel.  
To clean bicycles, use the detail brush.  
To clean equipment, use the detail  
brush, depending on the surface area.  
Finish by wiping down with a towel.  
SAVE THESE INSTRUCTIONS  
FOR HOUSEHOLD USE ONLY  
WARNING: This appliance is equipped with a grounded-  
type 3-wire cord (3-prong plug). This plug will only fit into an  
electrical outlet made for a 3-prong plug. This is a safety  
feature. If the plug should fail to fit the outlet, contact an  
electrician to replace the outlet. Do not attempt to defeat the  
safety purpose of the grounding pin, part of the 3-prong plug.  
concentrator to simply blow off dirt into  
the garbage can. When cleaning the  
detail brush, use a pair of pliers to hold  
and blow dirt as above or place in the  
basket of your dishwasher.  
Artificial Plants  
Use the concentrator without a brush  
attached to blow off the dust and dirt.  
Note: Wipe with a towel immediately  
before the cleaned area dries. When  
cleaning the oven, use the detail brush  
to clean around the elements and drip  
trays. Use the detail brush for cracks,  
crevices, and hard to reach areas.  
CAUTION: Always drain condensed water from hose  
before use or if unit has been left idle for a period of time. To  
drain hose, direct nozzle into an appropriate container or sink  
and depress hand grip steam trigger. Once hose has been  
drained, normal use may be resumed. Never direct nozzle  
towards people, animals or plants.  
Clothing  
A vapor cleaning system is excellent for  
removing wrinkles from fabrics. Simply  
“vaporize” the surface from a distance  
(12”-18”) The dry vapor removes  
wrinkles without leaving the fabric wet  
like ordinary fabric steamers do.  
Refrigerator - Use the concentrator to  
blow away dirt in the ice machine and  
on door seals. The vapor will not dry  
out or crack the seals as chemicals  
often do. Can openers and other  
kitchen equipment can be easily  
cleaned with the detail brush to get into  
all the nooks and crannies. Mold stains  
around door gaskets can be removed  
with the detail brush.  
Nicotine and Tar  
Nicotine and tar dissolves at high  
temperatures and becomes a light  
yellow oil that has the consistency of  
sewing machine oil. When the  
nicotine/tar film is touched by a hot terry  
cloth towel clipped over the floor brush,  
it immediately dissolves and flows into  
the towel. You can remove it from flat  
surfaces as fast as you can move the  
brush over the surface.  
To clean microwaves or other small  
appliances use the detail brush for  
small areas.  
Note: When cleaning small electrical  
appliances always unplug them from  
outlet before cleaning.  
To clean counter tops, use the floor  
brush with a terry cloth towel attached.  
For heavily soiled areas, use the brush  
without the terry cloth towel first in order  
to loosen the debris, then follow with a  
terry cloth towel attached to finish.  
Removing Wax, Tar, Etc.  
Many stains are only stuck on the  
surface of materials and can be easily  
and quickly removed by “blowing”  
excess material away from the surface  
from the side. This is accomplished by  
using the concentrator. Hold the terry  
cloth towel to the side to catch the loose  
residue as it is blown by the  
concentrator. Note: Always vacuum  
any loose residue off the surface before  
you apply vapor to it.  
2
13  
 
GETTING TO KNOW YOUR PORTABLE STEAM  
CLEANER w/CADDY  
TIPS ON HOW TO USE YOUR SYSTEM  
Fiberglass or Stainless Steel Surfaces  
Spot Cleaning (Carpets)  
Use the floor brush or detail brush.  
Slowly move the brush over the surface  
to be cleaned. The vapor will emulsify  
the dirt and grease on the surface.  
Follow behind with a terry cloth towel  
over the brush to remove excess  
moisture and residue.  
Tip: An old idea for polishing stainless  
steel is to wipe it down with seltzer soda  
water after it is cleaned.  
Use the concentrator with or without the  
detail brush. Move slowly over the soiled  
area, allowing the steam to penetrate.  
Agitate with detail brush or clean towel.  
Dab the spot with the towel (do not rub).  
Repeat as necessary to remove stain.  
Vacuum only after the carpet has  
completely dried.  
Always test color fastness of carpet in an  
inconspicuous area before cleaning.  
If your portable steam cleaner fails to  
remove stubborn stains a commercially  
available carpet shampoo may be  
required.  
Soap Scum  
Soap scum dissolves almost immediately  
under a combination of heat and  
moisture. Rinse the surface with a small  
amount of water afterwards or go back  
over it once more with a clean terry cloth  
towel.  
Do NOT add cleaning solutions, scented  
perfumes, oils or any other chemicals to  
the water used in this appliance as this  
may damage the unit or make it unsafe  
for use.  
Note: Soap scum sometimes will develop  
a hard surface from waterborne minerals.  
If this is the case, use the floor brush with  
no towel first to break up this surface - or  
spray or wipe first with lemon, vinegar or  
seltzer soda water to soften the minerals.  
Moving too slowly can dry out the soap  
scum and cause it to granulate on the  
surface. The surface will have a gritty  
feel. If this happens, apply vapor to the  
surface with the open brush again and  
re-clean.  
Upholstery  
Use the floor brush attached directly to  
the hand grip with a clean white terry  
cloth towel. Use fast, light strokes, avoid  
getting the fabric wet. Be patient with  
stubborn spots; work on a spot gently for  
no more than a minute at a time, then  
wait five minutes for the area to dry and  
repeat. Use circular movements or back-  
and-forth and side-to-side movements to  
get all sides of surface fibers then blot  
with a towel. Finish with a brushing in  
one direction that will give the fabric a  
uniform appearance.  
Garden Furniture  
Use any of the brushes depending on the  
surface area. Work quickly when  
cleaning resin outdoor furniture. Finish by  
wiping with a towel  
CAUTION: Always determine  
the color-fastness of any fabric-  
Blinds  
especially with reds or blues - by taking a  
clean, moist, warm towel and gently  
rubbing a small area as far down on the  
back or other out of the way place on the  
furniture as possible. If color comes off  
on the towel, you may need to have the  
piece dry cleaned.  
Use the detail brush to clean blinds.  
Move the brush over the surface,  
allowing enough time for the vapor to  
penetrate. Work quickly on PVC blinds.  
Test for color fastness on fabric blinds  
before using. Finish by wiping with a  
towel.  
1. Safety Filler Cap  
11. Rear Locking Latch  
12. Hand Grip Storage  
13. Castors (x4)  
14. Extension Tubes (x2)  
15. Window Squeegee  
16. Floor Brush  
2. Shoulder Strap  
3. Power “On” Light (Red)  
4. Steam Ready Light (Green)  
5. Flexible Hose  
6. Steam Switch  
Window, Glass Surfaces and Mirrors  
Use the dual edge glass and tile  
squeegee. Work with the vapor jet on  
using the top to bottom movements. Use  
the squeegee with the vapor off to clear  
the water from the glass. To do this  
without leaving streaks, use lateral  
movements from the top to the bottom of  
the surface.  
Bathroom Areas  
7. Locking Button  
8. Power Cord  
9. Front ,Locking Tab  
10. Caddy  
17. Triangular Brush  
18. Concentrator  
19. Funnel  
To clean the bathtub or shower area, use  
the detail brush for grout, shower door  
tracks, hard to get areas and heavily  
soiled areas. The dual edge window/tile  
squeegee will be the most efficient way  
to clean the rest of the area. Allow plenty  
of time for the heat to penetrate the  
surface. This is especially helpful in the  
shower area if there is tile or grout. Wipe  
with towel.  
20. Nylon Bristle Brushes (x2)  
Technical Specifications  
Voltage:  
120V., 60Hz.  
1550 Watts  
Power:  
Water Capacity:  
Steam Generator:  
40 US Fl. Oz. (1200 ml.)  
Stainless Steel  
Removal of soap scum on tile, grout, and  
shower doors is also easier with the  
steam cleaner.  
3
12  
 
TIPS ON HOW TO USE YOUR SYSTEM  
FEATURES OF PORTABLE STEAM CLEANER WITH  
CADDY  
Water  
Wood, Vinyl and Marble Floors  
Use tap water for all your cleaning  
4. Heavy-duty crush-resistant  
hose.  
1. No more detergents or  
chemicals. Just add water.  
Use the floor brush with a terry cloth  
attached. Move the brush across the  
floor as if you are mopping. When the  
towel is soiled, allow to cool, then turn  
the towel over or replace it with a clean  
towel. If you are working on a very dirty  
area, you can move the brush over the  
area slowly, several times. If it is a  
wood floor, move fast to avoid heat or  
moisture buildup in the wood. By  
needs.  
However, if you live in an area with  
hard water, use de-mineralized /  
distilled water when steaming light  
colored fabrics to eliminate the  
possibility of hard water stains.  
IMPORTANT: Do NOT add cleaning  
solutions, scented perfumes, oils or any  
other chemicals to the water used in  
this appliance. Use tap water or  
distilled/purified water if the tap  
water in your area is very hard.  
cleaning with the towel over the brush,  
you will not affect the shine on the floor.  
To Strip Wax: Use floor brush for open  
areas; detail brush for corners or tight  
areas - no towel, slow strokes. Work a  
small area at a time - remove the  
emulsified wax from the floor. When all  
of the wax has been stripped,  
immediately clean the floor and brushes  
with water before residue has a chance  
to harden on them. Go back over the  
stripped area with the floor brush with a  
towel to remove any remaining residue  
before waxing.  
5. Versatile, quick-change  
accessories  
2. Lightweight & Portable  
WARNING: A towel wrapped  
around the brush can become hot  
enough to burn. Make sure that you let  
the towel cool off for 5 minutes before  
touching it.  
Using Towels  
For best results use 100% cotton  
white terry cloth towels.  
Use correct size of towel to allow you  
to wrap the towel around the brushes  
and clip it under the spring loaded  
cloth holder.  
To Clean Waxed Floors: Wrap clean  
towel around the floor brush, brush  
quickly. This will cause the dirt to be  
removed but not the wax.  
The purpose of using a towel is to  
absorb moisture and dirt being  
removed. Always use dry towels.  
A wet towel will smear the dirt.  
Wash towels with strong detergent  
and bleach.  
Using scented fabric softener while  
washing the towels will cause the  
scent to be released into the air  
when using the towels with your  
steam system.  
6. Indoor and Outdoor Use:  
Bathrooms, kitchens, living  
areas, pet areas and  
appliances.  
3. Stainless Steel Boiler:  
Non-corroding, stainless  
steel boiler. Welded  
construction.  
Vinyl Floors: Do not allow heat to  
buildup in any kind of vinyl, since it can  
soften it enough to affect its texture.  
Work fast on vinyl.  
Automotive, patio and  
windows.  
Tile Floors: Use the concentrator with  
the detail brush attached to an  
extension. Have the floor brush with  
cloth attached ready as well. Clean the  
grout between the tiles with the detail  
brush. Remove the detail brush and  
attach the floor brush, move the brush  
across the floor to clean the tile and  
remove excess moisture and residue.  
For areas of tile that are very dirty,  
remove the towel and agitate with the  
brush. Do not let the area dry before  
you wipe with a towel.  
Efficient Work  
For vertical surfaces, wipe with a  
towel from the top down, in this  
way the dirty water will not soil  
surfaces already cleaned.  
Avoid changing brushes back and  
forth while cleaning.  
Start with the smallest brush to  
clean tight spots and corners first.  
Use a towel to wipe dirt as soon as  
possible, otherwise it will dry and  
re-adhere to the surface.  
4
11  
 
OPERATING INSTRUCTIONS  
CARE & MAINTENANCE  
Remove the funnel slowly and let  
Components  
If you consistently use demineralized or  
distilled water, cleaning the tank is  
unnecessary.  
To Descale the Steam Cleaner  
Step 1: Unplug the steam cleaner from  
the power source before you  
the remaining water in it to go  
inside the water tank. Do Not  
Overfill. Replace the Safety  
Filler Cap.  
Power “On” Light (red): This light will  
illuminate when the unit is plugged into  
the 120V. wall outlet. This light will cycle  
on and off with the steam ready light.  
CAUTION: Read the instructions  
for “Filling the Water Tank” before  
opening the Safety Cap.  
descale the boiler. Allow to cool.  
Rinsing Out the Steam Cleaner  
Normally, a periodic rinse of your portable  
steam cleaner will free it from deposits.  
This is recommended every 10-15  
tankfulls, to free up any scale deposits  
from the tank.  
Fill the boiler with 20 oz. of water and  
shake the cleaner vigorously. Tilt the  
cleaner upside down to empty the boiler of  
water and any scale deposits.  
Step 2: Fill the boiler with 1 part  
vinegar and 5 parts water and  
leave overnight or for a period  
of approximately 8 hours. Do  
not screw the safety/filler cap  
onto the steam cleaner while  
you are descaling the boiler.  
Do not use the steam cleaner  
while descaling solution is  
inside the boiler.  
WARNING:Allow unit to cool  
for 15 minutes before refilling.  
When refilling the steam cleaner  
while the boiler is still hot, there is  
a risk that water will squirt back  
during filling and cause scalding.  
Extreme care should be taken  
when refilling the unit. Use  
caution when opening the  
CAUTION: Always unplug  
before filling. ALLOW UNIT TO  
COOL FOR FIFTEEN (15)  
MINUTES BEFORE REFILLING.  
IMPORTANT: Do NOT add cleaning  
solutions, scented perfumes, oils or any  
other chemicals to the water used in this  
appliance. Use tap water or  
distilled/purified water if the tap water  
in your area is very hard.  
Safety/Filler Cap as cap may  
become hot during use and  
escaping steam can cause  
Step 3: After the period of soaking, turn  
the steam cleaner upside down  
to empty solution from the  
Descaling Your Steam Cleaner  
If the tap water in you area contains a high  
level of calcium deposits and you have  
been using tap water to do your steam  
cleaning, you should descale your unit  
after 10-15 tankfulls.  
scalding.  
Step 6: Connect desired attachments  
onto the Flexible Steam Hose.  
Step 7: Plug the unit into a standard (120  
volt, grounded) wall receptacle.  
Allow approximately 8-10 minutes  
for vapor to reach its working  
temperature and pressure. The  
green ready light will illuminate  
when the unit is ready for use.  
Always point nozzle outlet in a safe  
direction.  
Filling or Refilling Your Steam  
Cleaner With Water  
boiler. Due to the fact that a  
small amount of solution will be  
left in the boiler, it is necessary  
to rinse the boiler out with clean  
water 2 or 3 times. Your steam  
cleaner is now ready for use.  
IMPORTANT: Always insure that the unit  
is “UNPLUGGED” from the wall receptacle  
prior to initial filling or re-filling the water  
tank and has been allowed to cool for 15  
minutes. Never attempt to fill this unit  
under a water tap, always use the filling  
funnel provided.  
Step 1: Before refilling the steam cleaner,  
make sure that the unit is NOT  
plugged in and has been allowed to  
cool for fifteen (15) minutes.  
NOTE: When the steam cleaner has run  
out of water, steam output will cease.  
Step 2: Plug the power cord in to an electrical  
outlet and press the steam switch on  
the hand grip to the “ON” position to  
vent of any residual steam that is in  
the boiler.  
Fig. 1  
Step 3: Remove the power cord from the  
electrical outlet and turn the steam  
switch on the hand grip to the “OFF”  
position.  
Step 4: Place the unit on a flat, stable  
surface. Slowly turn the safety filler  
cap counter clockwise until it is  
removed.  
Step 5: Insert the funnel into the tank  
opening and add 40 US Fl, Oz.  
(1200 ml) of water. (Fig. 1) Place the  
funnel in the tank opening as  
WARNING:Allow unit to cool  
for 15 minutes before refilling.  
Use caution when opening the  
Safety/Filler Cap as cap may  
become hot during use and  
escaping steam can cause  
scalding.  
illustrated in Fig. 1. The funnel has  
been specially designed to show  
when the water tank is full. When  
water starts to come out of the vent  
hole of the funnel, the tank is full.  
5
10  
 
OPERATING INSTRUCTIONS  
OPERATING INSTRUCTIONS  
Attaching the Shoulder Strap  
Assembling the Caddy  
Using Your Steam Cleaner  
with Floor Brush  
Step 1: Connect one of the extension  
tubes to the hand grip on the  
flexible steam hose. To  
Attaching a Towel to the Floor  
Brush  
100% white terry cloth towel can be fitted  
on this brush, so as to absorb the dirt and  
protect delicate surfaces.  
Important: Please note that bristles may  
break through thin towels. To cut and make  
your own towels, we recommend that you  
use one (1) towel 8” x 17” folded in half or  
two (2) towels 4” x 17” laid one on top of  
the other be used. This will ensure that the  
brush bristles do not break through and  
that the towels will be sufficiently absorbent  
and retain as much dirt as possible.  
Using the detachable shoulder strap  
allows for greater freedom of movement  
when both hands are needed for  
various cleaning tasks.  
To attach the shoulder strap to the  
steam cleaner, simply snap the  
shoulder strap hooks onto the  
connecting rings on the unit body.  
See Fig. 17, 18 & 19.  
The casters for the caddy for the  
portable steam cleaner are packed  
and shipped unassembled. To  
assemble the casters to the caddy,  
simply insert the caster stem into one  
of the four (4) holes in the base and  
push downward with the palm of your  
hand. (Fig. 20.) Repeat for the next  
three (3) casters.  
attach the extension tubes  
one onto the other or onto the  
hand grip, press the locking  
button ensuring that it fits into the  
hole. (Fig. 2, Fig. 3) To  
disconnect, repeat the operation  
by pressing the locking button  
and pulling the two sections  
apart.  
Fig. 17  
Very Important: When installing the  
towels to the floor brush, ensure that the  
towels do not cover the front and the back  
of the brush. (See Fig. 9)  
Fig. 20  
Attaching the Portable Steam  
Cleaner to the Caddy  
1. After you have inserted the castors  
to the base of the caddy, turn the  
caddy right side up on a flat, level  
surface. Place it with the rear  
locking latch to your right.  
Fig. 2  
Fig. 3  
Fig. 18  
NOTE: Fit floor brush with the angle  
adapter on to the extension  
tube.  
Step 2: If the angle adapter is not  
attached to the floor brush, hold  
the brush with its bristles up in  
your left hand. With the angle  
adapter pointing downward,  
insert it into the hole in the back  
of the brush, then turn the floor  
brush 180°.  
Step 3: Insert the electrical power cord  
into the wall outlet. Heating  
time is approximately 8-10  
minutes with cold water. Filling  
the steam generator with hot  
water will shorten the heat up  
time.  
2. Hold the portable steam cleaner  
with the power cord also to your  
right.  
3. Insert the left side of the  
portable steam cleaner (#1 in the  
illustration below) down into  
the caddy making sure that it  
clips into the front locking tab.  
4. Then press down on the right  
side of the portable steam  
Fig. 5  
1. Prepare white terry cloth towel:  
size 8” x 17” folded in half or place one  
on top of another to have two layers.  
(Fig. 5)  
Fig. 19  
cleaner (#2 in the illustration  
below) so that the rear locking  
latch locks in place. (Fig. 21)  
2. Place the brush on top of the towel.  
Cleaning the Floor Brush  
To clean the floor brush after you have  
finished using:  
1. Lift the front clip on the floor  
brush (Fig. 4) and remove the brush.  
2. Rinse the bristle brush and the  
diffuser housing under warm water.  
3. Replace bristle brush onto the diffuser  
housing.  
IMPORTANT: When using the  
portable steam cleaner with the  
shoulder strap, avoid rocking or  
tilting the unit excessively as this  
may cause water to enter the  
hose and be discharged along  
with the steam.  
Front  
Locking  
Tab  
Rear  
Locking  
Latch  
Fig. 6  
3. Fold the towel as shown in Fig. 6.  
Fig. 21  
Fig. 4  
6
9
 
OPERATING INSTRUCTIONS cont.  
OPERATING INSTRUCTIONS  
WARNING: Always insure the  
Attaching the Accessories to  
the Flexible Steam Hose  
Attaching a Towel to the  
Triangular Brush  
100% white terry cloth towel can be fitted  
on this brush, so as to absorb the dirt and  
protect delicate surfaces.  
Important: Please note that bristles may  
break through thin towels. We recommend  
that two (2) towels, laid one on top of the  
other be used. This will ensure that the  
brush bristles do not break through and  
that the towels will be sufficiently absorbent  
and retain as much dirt as possible.  
unit is “UNPLUGGED” from the  
wall receptacle prior to attaching  
or removing accessories.  
Dual Edge Glass & Tile Squeegee  
This attachment is very useful for  
cleaning large windows, plastic material,  
ceramic, tiled or marble surfaces.  
Using Your Steam Cleaner  
with Triangular Brush  
To attach the triangular brush to the  
angle adapter, hold angle adapter in  
your right hand and the brush in your  
left. Insert the angle adapter into the  
triangular brush and turn 180° to lock  
in place. (Fig. 10 )  
To use: Connect the tile  
squeegee to the hand  
grip or use with  
Fig. 7  
extension tube for  
4. Fold the other side of the towel as  
shown in Fig. 7.  
hard to reach surfaces.  
Apply steam abundantly, rub with the  
soft spongy edge, then remove excess  
water and dirt with the glass wiping  
edge.  
Very Important: When installing the  
towels to the triangular brush, ensure that  
the towels do not cover the front and the  
back of the brush. (See Fig. 16)  
IMPORTANT:When cleaning  
windows, always avoid any sudden  
changes in temperature to prevent glass  
breakage or cracks.  
Fig. 13  
Fig. 8  
Concentrator  
Attach the concentrator  
to the handgrip or to the  
extension tubes. Then  
attach the detail brushes  
To the concentrator.  
5. Place the corner under the cloth  
holder as shown in Fig. 8.  
Fig. 10  
Step 1: The triangle brush w/angle  
adaptor connects either  
directly to the handgrip or  
may be used with the  
1. Prepare white terry cloth towel:  
size 8” x 17” as shown in Fig. 13.  
Detail Brush  
It is best for cleaning grout in-between  
the tiles, ceramic and marble.  
To use: Attach the detail  
brush on to the end of the  
concentrator, which  
then may be used directly  
on the hand grip or with extension tubes  
2. Place the brush on top of the towel.  
extension tubes. To connect  
the extension tubes to the  
hand grip attach the  
extension tubes one onto the  
other and then onto the hand  
grip. (Fig. 11 & 12) To  
disconnect, reverse the  
operation by pressing the  
locking button and pulling the  
two sections apart.  
3. Fold the towel  
as shown in  
Fig. 14  
Fig. 9  
Fig. 14  
6. Place the towel around the brush,  
and repeat folding the towel as shown  
in Fig. 9. When folding the towel,  
leave some slack. Do not pull tightly  
around the brush, leave some  
looseness.  
4. Place the  
corner under  
the cloth  
Fig. 11  
holder.  
(Fig. 15)  
Fig. 15  
5. Fold the other  
side of the towel  
in the same way  
and place the  
Fig. 16  
corner under the  
cloth holder.  
(Fig. 16)  
Fig. 12  
7
8
 

Cortelco Personal Computer WPBX00 PRO MAN User Manual
Crate Amplifiers Musical Instrument Amplifier RFX15 User Manual
Cuisinart Refrigerator CWC 1600 User Manual
Cypress Computer Hardware CY62148E User Manual
Dell Server BMX01 User Manual
Edelbrock Air Cleaner 8679 User Manual
Exergen Scanner DT 1001 User Manual
Fender Guitar 011 7602 User Manual
Frigidaire Cooktop FGGC3645K S W B User Manual
Fundex Games Games PARTY IN MY TUMMY User Manual